Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
What are your opinions about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough job. If the old bathtub is easily easily accessible, the job can move quickly; if you have to open up a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is much harder. In either situation, the task is within a residence handyman's abilities, although you will need an assistant to leave the old tub and also embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is far better to consider employing one before you start. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your restroom if you have actually currently purchased a brand-new bathtub and don't require to transform the arrangement of your previous water pipes.
Your tools as well as product list need to comprise the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome as a result of the restricted access that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the remaining water that will originate from the pipes. Once the supply pipelines have been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Using both wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bathtub till the spirit level reads degree.
To install faucets, fit all-time low of the furthest adaptable tap port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water supply and also check all joints and also new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the bath tub has been used a minimum of when as this will certainly resolve it right into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers are in place in between the faucet and the sink. Protect the faucet in place with the maker supplied backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, leading to problems with moisture as well as possible leaks to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealer can break fairly very early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads on Installing A Bathtub, I thought sharing that chunk was beneficial. Loved our blog posting? Please share it. Let others find it. Thank-you for taking the time to read it.
Dial, rest easy! Report this page